Building progress LACoFD Lifeguard Ford F-350

[Hazmat]

Followed by the compartment door handles...

LACOFD_LG (71) (Large).JPG (146.18 KiB) Viewed 4265 times

LACOFD_LG (72) (Large).JPG (169.84 KiB) Viewed 4265 times

...the roof lights, out of tiny, self adhesive gemstones...

LACOFD_LG (73) (Large).JPG (222.52 KiB) Viewed 4265 times

...and the diamond plate parts for the rear and top compartment surface together with some L-shape rods as rain gutters.

LACOFD_LG (74) (Large).JPG (301.89 KiB) Viewed 4265 times

I further built the rack attachments for the surfboard and the stretcher out of T- and U-shape rods.

LACOFD_LG (76) (Large).JPG (295 KiB) Viewed 4265 times

LACOFD_LG (80) (Large).JPG (185.9 KiB) Viewed 4265 times

[Hazmat]

The next step was to paint the compartment doorhandles chrome, using the "Molotow Liquid Chrome pen".
Some of you probably noticed that I meanwhile "shrunk" the compartment door handles, since they were out of scale.
I already noticed it after painting, but I thought when adding the chrome it will look ok Exactly the opposite happened, it pretty much highlighted the error further
So I ended up filling the former holes, drilling smaller ones into it and then repainting the whole part
Always something with my projects

LACOFD_LG (84) (Large).JPG (195.66 KiB) Viewed 4265 times

LACOFD_LG (85) (Large).JPG (188.81 KiB) Viewed 4265 times

Then I completed the towing hitch.

LACOFD_LG (86) (Large).JPG (287.68 KiB) Viewed 4265 times

LACOFD_LG (87) (Large).JPG (270.82 KiB) Viewed 4265 times

And the truck at this stage

LACOFD_LG (82) (Large).JPG (278.88 KiB) Viewed 4265 times

LACOFD_LG (83) (Large).JPG (274.95 KiB) Viewed 4265 times

[Hazmat]

I continued with the equipment like the rescue can/buoy.
Therefore I used 1,5mm, 1mm strip styrene and a 1mm styrene round rod.

LACOFD_LG (94) (Large).JPG (285.01 KiB) Viewed 4265 times

LACOFD_LG (95) (Large).JPG (281.48 KiB) Viewed 4265 times

The styrene rod was cut to an small arrow and the round rod was then horizontaly wrapped around it.

LACOFD_LG (96) (Large).JPG (283.49 KiB) Viewed 4265 times

LACOFD_LG (97) (Large).JPG (275.7 KiB) Viewed 4265 times

finally I added the 1mm styrene strip on top of the arrow. But since I filled the 1mm strip about half way down, i suggest a 0,5mm strip would do the job I think the outcome pretty much looks like the rescue can, even without paint on.

LACOFD_LG (99) (Large).JPG (328.1 KiB) Viewed 4265 times

LACOFD_LG (100) (Large).JPG (268.27 KiB) Viewed 4265 times

[Hazmat]

And the rescue cans with paint and some rope on

LACOFD_LG (119) (Large).JPG (258.95 KiB) Viewed 4265 times

LACOFD_LG (146) (Large).JPG (295.9 KiB) Viewed 4265 times

The other, nice feature were the swim fins.
These were made out of 1mm and 0,5 mm styrene sheet and strip styrene.

LACOFD_LG (104) (Large).JPG (285.01 KiB) Viewed 4265 times

LACOFD_LG (106) (Large).JPG (319.26 KiB) Viewed 4265 times

LACOFD_LG (108) (Large).JPG (303.31 KiB) Viewed 4265 times

LACOFD_LG (116) (Large).JPG (288.97 KiB) Viewed 4265 times

[Hazmat]

For the rear handles on top of the compartments I simply used paper clips, cut to size.

LACOFD_LG (128) (Large).JPG (325.35 KiB) Viewed 4265 times

LACOFD_LG (130) (Large).JPG (325.79 KiB) Viewed 4265 times

meanwhile I also painted the diamondplates with the Molotow pen. It worked perfectly even with this, rather big, surface

LACOFD_LG (132) (Large).JPG (260.97 KiB) Viewed 4265 times

Then I punched out some side reflectors, out of reflective sheet.

LACOFD_LG (89) (Large).JPG (297.81 KiB) Viewed 4265 times

LACOFD_LG (90) (Large).JPG (148.6 KiB) Viewed 4265 times

[Hazmat]

Next I concentrated on the emergency lights.
To create them I punched out round lights of self adhesive clear gemstone/decoration stickers and cutting out rectangular shapes as well. Finally I even painted a small, tiny chrome trim around the rectangular lights.

LACOFD_LG (121) (Large).JPG (327.59 KiB) Viewed 4265 times

The rear part was further completed with tiny round red gemstones.

LACOFD_LG (133) (Large).JPG (199.67 KiB) Viewed 4265 times

LACOFD_LG (134) (Large).JPG (223.73 KiB) Viewed 4265 times

LACOFD_LG (135) (Large).JPG (224.93 KiB) Viewed 4265 times

LACOFD_LG (137) (Large).JPG (233.25 KiB) Viewed 4265 times

LACOFD_LG (138) (Large).JPG (274.41 KiB) Viewed 4265 times

[Hazmat]

Further parts were the rear scene lights out of clear plastic pins and ferrules.

LACOFD_LG (139) (Large).JPG (322.43 KiB) Viewed 4264 times

LACOFD_LG (143) (Large).JPG (176.79 KiB) Viewed 4264 times

A modified FRR MX lightbar.

LACOFD_LG (140) (Large).JPG (213.72 KiB) Viewed 4264 times

LACOFD_LG (141) (Large).JPG (199.38 KiB) Viewed 4264 times

Antennas

LACOFD_LG (144) (Large).JPG (311.08 KiB) Viewed 4264 times

And even small, fingernail gemstones as rear cabine/brake light

LACOFD_LG (136) (Large).JPG (230.45 KiB) Viewed 4264 times

[Hazmat]

To conclude this build walkthrough the creation of the life wests out of the former IXO FDNY Engine "hoses"

LACOFD_LG (147) (Large).JPG (285.22 KiB) Viewed 4264 times

LACOFD_LG (148) (Large).JPG (286.59 KiB) Viewed 4264 times

LACOFD_LG (149) (Large).JPG (286.67 KiB) Viewed 4264 times

LACOFD_LG (151) (Large).JPG (257.13 KiB) Viewed 4264 times

LACOFD_LG (152) (Large).JPG (230.88 KiB) Viewed 4264 times

[Hazmat]

Since I haven´t made a picture of the finished wests, here some closeups with everything together

LACOFD_LG1 (54) (Large).JPG (215.95 KiB) Viewed 4264 times

LACOFD_LG1 (144) (Large).JPG (191.37 KiB) Viewed 4264 times

LACOFD_LG1 (147) (Large).JPG (195.2 KiB) Viewed 4264 times

To end this, a final shot of the whole rig

LACOFD_LG1 (66) (Large).JPG (201.13 KiB) Viewed 4264 times

I hope you liked it and I could answer some questions

[JoeO]

Thanks for sharing and taking the time to download all the information!